If water is spilling over on the intake side of your AquaClear, or the flow from the filter has slowed down, the manufacturer’s manual gives a short list of causes: the flow control setting, dirty media, a clogged intake sponge, and a dirty or worn impeller assembly. This guide follows Fluval’s official AC Series manual.

Quick answer: Check that the flow control lever isn’t set low. Then rinse the filter media and the intake sponge, and clean the impeller assembly. If the impeller is worn, replace it. A high water level with water spilling over on the intake side most likely means the media is clogged.
Safety first: Always unplug the filter before you put your hands in the water or take parts apart. Don’t use soaps or detergents to clean it.
This is based on Fluval’s official manual for the AC Series (the AC110 edition), whose troubleshooting FAQ covers the AC20, AC30, AC50, AC70 and AC110. If you own an older AquaClear, check the manual that came with it.
Step by step: what to check

Step 1: Check the flow control lever
The manual says that when the flow control lever is set to its minimum position, up to 50% of the water is recirculated for slower but more thorough filtration. A low setting therefore gives a slower output on purpose. Once the filter is running, adjust the lever to the output you want.
Step 2: Rinse the filter media
The manual says that if the flow is slower than normal, the media is likely dirty and in need of cleaning or replacement. In the AC110, water passes through the Bio-Foam, carbon and BIOMAX before it returns to the aquarium. Rinse the media in clear lukewarm water and don’t use soaps or detergents. The manual recommends regular cleaning of the filter and its parts every month. The media in your model may differ, so check your manual.
Step 3: Rinse the intake sponge
The manual recommends rinsing the intake strainer sponge monthly and replacing it every two months. It adds that you may need to rinse it more often, depending on your aquarium.
Step 4: Clean the impeller assembly
The manual says the impeller assembly may also need cleaning. Unplug the filter, remove the motor, pull the impeller out of the impeller well and rinse it. Our impeller cleaning guide lists the steps.
Step 5: Check the tank water level
The manual gives a minimum water level for the filter to work properly. For the AC20, AC30 and AC50, the water level should be no more than 5/8 in (16 mm) from the bottom of the filter output. For the AC70 and AC110, it should be no more than 1.5 in (38 mm) from the bottom of the filter output.
Step 6: Replace a worn impeller
The impeller is the filter’s only moving part and runs around the clock, so it eventually wears. The manual says a worn impeller is not covered by the warranty. For the AC110, the manual’s spare parts list gives the impeller assembly as item A638. Check your own manual for your model’s part number.
Why is water spilling over on the intake side?
The manual says this is likely the result of filter media that is clogged and isn’t letting water pass through efficiently. Rinsing the media regularly helps prevent it.
Quick reference
| What you see | What the manual says it likely means | What to do |
|---|---|---|
| Water level high and spilling over on the intake side | Filter media is clogged | Rinse the media regularly |
| Flow slower than normal | The media is dirty, or the impeller assembly needs cleaning or replacing | Clean or replace the media, clean the impeller assembly, replace a worn impeller |
| Slower output with the lever at its minimum | The minimum setting recirculates up to 50% of the water | Adjust the lever once the filter is primed |
Frequently asked questions
Why is the flow from my AquaClear slower than normal?
The manual says the media is likely dirty and in need of cleaning or replacement. It is also possible that the impeller assembly needs cleaning, or that the impeller needs replacing.
Why is water spilling over on the intake side?
The manual says this is likely caused by clogged filter media that isn’t letting water pass through efficiently. Rinse the media regularly to help prevent it.
How often should I clean the intake sponge?
The manual recommends rinsing the intake strainer sponge monthly and replacing it every two months. You may need to rinse it more often depending on your aquarium.
Does the flow control lever change the flow?
Yes. At its minimum position, up to 50% of the water is recirculated for slower but more thorough filtration. After priming, adjust the lever to the output you want.
Do I need to replace the filter media?
The manual says dirty media may need cleaning or replacement. Its maintenance frequency chart lists which parts to check, rinse or replace at monthly, two-monthly and three-monthly intervals.
What this page doesn’t cover
This page covers the filter equipment only. It doesn’t give fish-health, medication or water-chemistry advice, and it doesn’t describe electrical repair.
Sources and last verified
- Fluval, AquaClear AC Series instruction manual (AC110 edition, official PDF): fluvalaquatics.com
Last verified: November 19, 2026, against the safety instructions, quick start guide, maintenance section and troubleshooting FAQ in that PDF.
