The EHEIM thermocontrole is an adjustable aquarium heater with a temperature range of 20 to 32°C (68 to 90°F) and a stated accuracy of 0.5°C (1.0°F). This guide follows the manufacturer’s manual: how to choose a size, mount the heater, set the temperature, read the control light and handle it safely.

Illustration of an aquarium with a heater, a temperature gauge and green and red indicator lights
Illustration, not a photo of a specific product.

Quick answer: Mount the heater upright and below the water, in an area of strong water flow, with at least the MIN. WATER LEVEL marking under water. Turn the adjusting ring all the way back to the stop, then set the temperature you want. The control light is red while the heater is heating and turns green when the set temperature is reached. Keep checking the water temperature with your own thermometer.

Safety first: Disconnect all electrical equipment in the aquarium from the mains before you put your hands in the water or fit or remove parts. The heater is very hot during and right after use. Never touch the heating zone.

Which size does the manual list for each tank?

The manual lists ten models, from 25 W to 400 W, and gives a tank volume range for each one. Use this as the manufacturer’s guide and check the label on your own heater.

ModelPowerTank volume (litres)Tank volume (US gallons)Length
363125 W20 to 255.2 to 6.6233 mm
363250 W25 to 606.6 to 15.8233 mm
363375 W60 to 10015.8 to 26.4260 mm
3634100 W100 to 15026.4 to 39.6309 mm
3635125 W150 to 20039.6 to 53309 mm
3636150 W200 to 30053 to 79335 mm
3637200 W300 to 40079 to 106396 mm
3638250 W400 to 600106 to 159442 mm
3639300 W600 to 1000159 to 264496 mm
3640400 W1000 to 1200not listed496 mm

The manual lists 120 to 127 V / 60 Hz and 220 to 240 V / 50 to 60 Hz versions (the 400 W model is 220 to 240 V only). The electrical data on the heater must match your mains supply, so check the label.

How to install the heater

  1. Inspect it first. Check that the heater, especially the mains cable and plug, is undamaged and that the glass body isn’t broken or cracked.
  2. Remove the transportation protection.
  3. Fit the suction cups to the suction cup mount, then attach the mount to the heater. Don’t place it over the heating zone or the control light.
  4. Attach the heater below the water level on the inside wall of the tank. Allow for the minimum water level and the maximum immersion depth.
  5. Put the heater where the water flows strongly. It needs to be washed by water for even heating.
  6. Mount it upright only. The manual says to install the heater in a vertical position.
Step-by-step checklist graphic: set up an EHEIM thermocontrole heater
Quick checklist. The full steps are below.

Never run the heater out of the water. It must be immersed at least to the MIN. WATER LEVEL marking before you use it.

How to set the temperature

  1. Plug the heater in. The control light comes on.
  2. Turn the adjusting ring all the way back to the stop (20°C or 68°F).
  3. Turn the ring to the temperature you want.
  4. Watch the control light. It is red while the heater is heating and turns green when the set temperature is reached.
  5. Check the water temperature at regular intervals.

To switch the heater off, unplug it.

What the control light means

LightWhat the manual says
RedThe heater is heating
GreenThe set temperature has been reached

If your own thermometer disagrees with the light and the water keeps getting warmer, see our guide to a heater that is stuck on.

Built-in protection and what the manual says not to do

How to remove and clean the heater

  1. Unplug the heater.
  2. Leave it in the water for at least 30 minutes to cool.
  3. Take it out of the tank and clean it under running water.

Don’t use hard objects or aggressive cleaning agents, and don’t wash it in a dishwasher. If you accidentally removed the heater while it was running, don’t put it back in the water and don’t touch hot surfaces. Unplug it and let it cool on a heat-resistant surface for at least one hour. Never put a hot heater on a heat-sensitive surface.

Guarantee and spare parts

The guarantee is 3 years. It does not include glass damage, improper use or opening the appliance. The manual lists spare parts: a pack of four suction cups (art. no. 7271100) and a suction cup mount with two suction cups (art. no. 7443900).

Frequently asked questions

What does the red light on an EHEIM thermocontrole mean?

It means the heater is heating. The light turns green when the temperature you set has been reached.

Can I lay the heater flat?

No. The manual says to install the heater in a vertical position only, below the water level and in an area of strong flow.

Can I use a timer or temperature controller with it?

The manual says this heater may not be operated with an additional timer or an additional control system.

What temperature range does it cover?

Eheim lists 20 to 32°C (68 to 90°F) with an accuracy of 0.5°C (1.0°F).

Can I wash the heater in the dishwasher?

No. The manual says the heater is not dishwasher-safe. Clean it under running water with no hard objects or aggressive cleaning agents.

What if the heater stays on past the temperature I set?

Unplug it and follow our guide to a heater that is stuck on. Eheim’s safety instructions say not to operate an appliance that is malfunctioning.

What this page doesn’t cover

This page covers heater equipment only. It doesn’t give fish-health, medication or water-chemistry advice, and it doesn’t describe electrical repair. It applies to Eheim thermocontrole models 3631 to 3640. Other heaters may differ, so check your own manual.

Sources and last verified

Last verified: November 19, 2026, against the English operating manual and the US safety instructions in that PDF.

Related guides