A heater that keeps heating after the water reaches the temperature you set is a safety problem, not a minor annoyance. This guide covers what to do first, based on the manufacturer’s own instructions, and when to stop using the heater.

Illustration of an aquarium heater beside a thermometer showing a high reading, with an unplugged power cable
Illustration, not a photo of a specific product.

Quick answer: If the heater keeps heating after the water has passed the temperature you set, treat it as faulty. Unplug it, check the real water temperature with a separate thermometer, and rule out simple causes such as the set point or an outside heat source. If the water still runs warm, stop using the heater and replace it or contact the manufacturer.

Safety first: Unplug the heater, and disconnect other tank equipment from the mains, before you put your hands in the water. The heater is very hot during and right after use, so don’t touch its heating zone.

This is based on the safety instructions in Eheim’s operating manual for its thermocontrole heaters (models 3631 to 3640). Other brands may differ, so check your own manual.

Signs your aquarium heater is stuck on

If you see either sign, follow the steps below.

What to do first: a 5-step checklist

Step-by-step checklist graphic: heater stuck on
Quick checklist. The full steps are below.

Step 1: Unplug it and let it cool in the water

Take the plug out of the outlet. Eheim says an unplugged heater should stay in the water for at least 30 minutes to cool before you remove it. If it was pulled out while running, don’t put it back in the water. Unplug it and let it cool on a heat-resistant surface for at least one hour.

Step 2: Check the real water temperature

Use a separate thermometer, not the heater’s dial or light. Eheim’s manual tells owners to check the water temperature at regular intervals, and it lists an accuracy of about 0.5°C (1.0°F) for its thermocontrole range. A reading far above your setting after the heater has had time to settle goes beyond that margin and points to a fault. Other brands list different figures, so check your manual.

Also look at the control light. On the Eheim thermocontrole, a light that stays red while your thermometer reads above the setting is worth reporting to the manufacturer.

Step 3: Rule out simple causes

Step 4: Don’t try to repair or adjust it

Eheim says repairs must be carried out by an Eheim service centre, that you should only do the work the manual describes, and that you should never make technical modifications. Its guarantee does not include opening the device. The manual doesn’t describe a user fix for a heater that won’t switch off. Some other heater lines have a calibration dial, so follow only your own heater’s manual.

Step 5: Stop using it and replace it or contact the manufacturer

Eheim’s safety instructions say not to operate an appliance that is malfunctioning. For this heater series the guarantee is 3 years, but it does not include glass damage, improper use or opening the appliance. Keep your receipt and model number when you contact the maker.

Quick reference: what you see and what to do

What you seeWhat it may meanWhat to do
A thermometer well above your setting and the heater light still onA possible heater faultUnplug it, follow the steps above and stop using the heater
A thermometer above your setting but the light shows the heater has reached temperatureA set point, outside heat or thermometer problemCheck the setting, look for outside heat and confirm with a second thermometer
A cracked glass body or damaged cordThe heater is not safe to useUnplug it, don’t use it again and contact the manufacturer

How to prevent a repeat

Frequently asked questions

Can I leave a stuck-on heater plugged in and keep an eye on it?

No. Eheim’s safety instructions say not to operate an appliance that is malfunctioning. Unplug it, check the water temperature with a separate thermometer, and replace the heater or contact the manufacturer.

Should I pull the heater out of the tank right away?

Not straight away. Eheim says to unplug it and leave it in the water for at least 30 minutes to cool before removing it. If it was removed while running, don’t put it back in the water. Let it cool on a heat-resistant surface for at least one hour.

How accurate should an aquarium heater be?

Eheim lists about 0.5°C (1.0°F) for its thermocontrole heaters, across a 20 to 32°C (68 to 90°F) range. Other brands list different figures, so check the manual for your model.

Can I recalibrate or repair a stuck heater myself?

Eheim says repairs must be done by an Eheim service centre and that you shouldn’t modify the heater. Its guarantee does not include opening the appliance. Some other heater lines have a calibration dial, so follow only your own heater’s manual.

Does the built-in thermal cutoff protect against a stuck heater?

In Eheim’s manual, the thermal circuit breaker is described for running without water or with a very low water level, and the heater restarts after cooling. It isn’t described as protection against the water getting too warm because of a thermostat fault, so don’t rely on it for that.

What should I do about my fish?

This page covers the heater, not your fish. If the tank has been very warm and fish look distressed, contact a local aquarium store or an aquatic vet right away.

What this page doesn’t cover

This page covers heater equipment only. It doesn’t give fish-health, medication or water-chemistry advice, and it doesn’t describe electrical repair.

Sources and last verified

Last verified: November 19, 2026, against the English operating manual and the US safety instructions in that PDF.

Related guides