If your AquaClear filter won’t start, or runs but won’t pull water, the manufacturer’s manual points to a short list of checks: the power, the water in the filter case, the intake tube, a clean impeller and the right priming steps. This guide follows Fluval’s official AC Series manual.

Quick answer: Make sure the cord is plugged in. Fill the filter case completely with water. Check that the intake U-tube is properly seated on the impeller cover. Clean the impeller, impeller shaft and impeller well. Then prime with the flow control lever on its lowest setting and allow 30 to 45 seconds.
Safety first: Always unplug the filter before you put your hands in the water or take parts off. Never run the filter without water.
This is based on Fluval’s official manual for the AC Series (the AC110 edition), whose troubleshooting FAQ covers the AC20, AC30, AC50, AC70 and AC110. If you own an older AquaClear, check the manual that came with it.
Step by step: what to check

Step 1: Check the power
Verify that the electrical cord is plugged into an outlet properly. If an RCD or GFCI has switched off, or the filter shows any sign of abnormal water leakage, the manual says to disconnect the power cord from the mains and remove the filter from the water. In that case, don’t try to repair it yourself. The manual says to return the appliance to an authorized service facility or discard it.
Step 2: Fill the filter case completely with water
Make sure the filter container is completely full of water. The manual warns against operating the filter without water and says not to let the filter pump run dry.
Step 3: Check the intake tube
Make sure the intake stem (the U-shaped tube) is properly seated on the impeller cover.
Step 4: Clean the impeller
Check that the impeller, impeller shaft and impeller well are thoroughly clean and free of debris. Unplug the filter before you take anything apart.
Step 5: Prime the filter the way the manual describes
- Fill the filter case completely with water.
- Set the water flow control lever on the intake U-tube to its lowest position for the initial start-up.
- Plug the power cord into the outlet.
- Allow 30 to 45 seconds for priming.
- When priming is finished, adjust the flow control to the output you want.
- Fit the filter cover.
The manual says the lowest setting also gives faster priming.
Check the tank water level
The manual gives a minimum water level for the filter to work properly. For the AC20, AC30 and AC50, the water level should be no more than 5/8 in (16 mm) from the bottom of the filter output. For the AC70 and AC110, it should be no more than 1.5 in (38 mm) from the bottom of the filter output.
Quick reference
| Symptom | What the manual suggests |
|---|---|
| The filter doesn’t start | Check the plug, fill the case with water, seat the intake tube, and clean the impeller, shaft and well |
| The filter runs but doesn’t pull water | Prime again: full case, flow lever at the lowest setting, 30 to 45 seconds |
| The filter is noisy | See our impeller cleaning guide |
| Water spills over on the intake side | See our low flow guide |
When the impeller may need replacing
The impeller is the filter’s only moving part and runs around the clock, so it eventually wears. The manual says it is therefore not covered by the warranty. For the AC110, the manual’s spare parts list gives the impeller assembly as item A638. Check your own manual for your model’s part number.
Frequently asked questions
How long does priming take?
The manual says to allow 30 to 45 seconds after plugging in, with the flow control lever on its lowest setting.
Why set the flow lever to the lowest position?
The manual says to use the lowest setting for the initial start-up and for faster priming. Once priming is complete, you can adjust the flow as you need.
Can I run an AquaClear without water?
No. The manual warns against operating the filter without water and says not to let the filter pump run dry.
Do I need to prime the filter again after cleaning it?
Yes. The manual’s cleaning instructions end by telling you to follow the operating instructions to restart and prime the filter.
What should I do if the GFCI or RCD trips?
The manual says to disconnect the power cord from the mains and remove the filter from the water, and not to attempt repairs yourself. Return it to an authorized service facility or discard it.
What if the filter still won’t start?
Fluval’s manual lists customer service contact details and a 3-year warranty with proof of purchase. The warranty does not cover wear and tear or parts that haven’t been maintained correctly.
What this page doesn’t cover
This page covers the filter equipment only. It doesn’t give fish-health, medication or water-chemistry advice, and it doesn’t describe electrical repair.
Sources and last verified
- Fluval, AquaClear AC Series instruction manual (AC110 edition, official PDF): fluvalaquatics.com
Last verified: November 19, 2026, against the safety instructions, quick start guide, maintenance section and troubleshooting FAQ in that PDF.
